Difference Between RG6 and RG59
RG6 vs RG59
Coaxial cables, commonly called ‘coax’, are the cables that are commonly used for video and satellites installations. There are many kinds of cables to suit different applications, among which are the RG59 and RG6. The main difference between the two is their construction as the RG6 is bigger compared to the RG59. The inner conductor core of the RG6 cable is thicker as well as the shielding within the rubber sheath.
The difference between the two, in terms of construction, results in a better frequency range for the RG6 cable. RG6 cables are often certified to work up to 3Ghz. Although RG59 cables may work above the 2Ghz level, it is not always the case and problems may still appear later as the conditions change. Another key difference is the much lower attenuation of RG6 cables. With very long lengths of cable, the attenuation can degrade the signal to a point where it becomes noticeable. Using an RG6 cable simply means that you are able to use longer cables before you have problems with attenuation.
A downside to the RG6 cable is when it is used for applications operate below 50Mhz. A good example of this is HDTV, which only operates at around 37Mhz. The shielding of RG6 cables cannot properly prevent noise at levels of below 50Mhz and the signal may be worse with an RG6 cable than with an RG56.
Because of these differences, each of these two cables are often used for specific purposes despite being interchangeable. RG6 is the cable of choice for satellite receivers because it allows for better signal quality as well as insurance that any future specification that could use frequencies close to 3Ghz would still be compatible with the current wiring. RG59 is used for video signals as it would provide the best signal quality for the frequencies in use. Not to mention the cheaper price per length of RG59 cables compared to RG6 cables.
Summary:
1. RG6 cable has a thicker conductor than the RG59
2. RG6 cable has better insulation than the RG59
3. RG6 can carry signals of much higher frequencies than the RG59
4. RG6 has much lower signal losses compared to the RG59
5. RG6 cable may not operate below 50Mhz while the RG59 can
6. RG6 is better for satellite signals while RG59 is better for video signals
7. RG6 cables cost more than RG59
- Difference Between Sony Cybershot S Series and W Series - December 22, 2012
- Difference Between Samsung Galaxy S3 and iPhone 5 - December 21, 2012
- Difference Between Samsung Galaxy S2 (Galaxy S II) and Galaxy S 4G - December 20, 2012
Search DifferenceBetween.net :
Email This Post
: If you like this article or our site. Please spread the word. Share it with your friends/family.
Doesn’t digital channel number 2 (lowest freq OTA station) operate a just above the 50 Mhz level? If so, then would RG6 be a better choice for a HDTV over the air antenna?
The lowest OTA is 54 MHz, so yes RG6 is a better choice for antenna use as well as satellite.
Even FM radio is 88-108 MHz, so RG6 is the better choice.
I had to downgrade the web article on the difference between RG-6 and RG-58 due to the fact that in the article it mentions RG-56. ‘The shielding of RG6 cables cannot properly prevent noise at levels of below 50Mhz and the signal may be worse with an RG6 cable than with an RG56.’
I wasn’t looking for information on RG56.
If this is an error, the article should be corrected.
I believe the reference to RG56 is just a typographical error and the reference should have been to RG59. My reasoning is that RG56 is a military version, has an impedance of 50 ohm, and is otherwise unmentioned at all in the article. Later, in the summary, the differential properties between RG6 and RG59 are exactly those attributed to the RG56.